Skip to main content

Search This Blog

CygnusAlpha

Posts

Showing posts from October 18, 2008

XBee USB

Get link
Facebook
X
Pinterest
Email
Other Apps

- October 18, 2008

XBee and the USB Interface arrived in the post today. The USB interface is FTDI based so I'll have to install the driver for MacOSX. Fun!

Powered by Blogger

(c) cygnusalpha..

CygnusAlpha

popular

Hacking the Sureflap Dual Scan Cat Flap

- July 24, 2018

Hacking the Sureflap Dual Scan Cat Flap To get the RFID codes for the 134.2 KHz Cat chip ID's Aha! A PIC. And an ICD port next to it. PICKit3 at the ready. I'd quite like to get the firmware off this if possible.

Getting FlashFloppy onto the Gotek SFRC922D

- October 12, 2018

These flash floppy emulators from Gotek are great. But they are even better when they have the FlashFloppy firmware loaded. The SFRC922D model I have seems to have some extra holes under the serial/boot jumpers. I chose to use the USB/DFU programming method for which you will need a USB A-A cable. Here's how I put the Gotek into boot mode for DFU: Jumpers for boot/DFU mode. Wirelinks above the white connector. Once in boot mode you can program the device using the dfu-util: I'm using OSX, and used homebrew to install the dfu-util. brew install dfu-util dfu-util --list dfu-util 0.9 Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc. Copyright 2010-2016 Tormod Volden and Stefan Schmidt This program is Free Software and has ABSOLUTELY NO WARRANTY Please report bugs to http://sourceforge.net/p/dfu-util/tickets/ Deducing device DFU version from functional descriptor length Found Runtime: [05ac:8206] ver=1965, devnum=2, cfg=1, intf=2, ...

Handling and Tyre wear patterns

- January 31, 2013

Racing last night at Bashley the car was still quite unstable. For the last few races I have been changing one setting at a time to pin down which are making improvements. So far I've stiffened the front springs, moved the shock positions on the rear and toed out the steering a little. The car was better but still quite hard to tame the back end.. If you look closely at the tyres you can just about make out that the insides of the tyres are a little duller meaning that the majority of the cars weight has been on the insides even during dynamic handling. This is a big clue to start looking at the camber adjustments. Camber is the angle of the wheel relative to the track looking from the front of the car. 0 degrees means the wheel is dead vertical. -5 degrees means the top of the wheel is angled toward the centreline of the car. A little negative camber can be useful, but evidently I had too much. I rather unscientifically reduced the amount and in the next heat the car was ...

Python Dependency Injection

- March 02, 2023

Python: importing settings or dependency injection Two common approaches to configuring a python application are importing settings and dependency injection. Importing settings involves creating a settings module or file that contains all the values and configurations needed for your application to run. These settings can then be imported into other modules and used directly. The advantage of this approach is that it is simple and easy to understand, and can work for small projects. The disadvantage is that it increases coupling to the settings module and to the way that those settings are collected. It also makes it harder to unit test a module or class without having to resort to mocking the settings module in some way. Dependency injection involves passing dependencies (such as settings) into a class as parameters, typically using a class method that sets some class variables. The advantage of this is that the class needs no knowledge of the settings module or ho...

Homebrew tapeless camera

- November 12, 2010

This is an ongoing project I'm working on which started as a circuit that I decided was necessary to be able to neatly interface the nNovia QC120 A 2D2 recorder to a Sony DXC-325P camera with CA-325P studio back. This interface deals with translating VTR start/stop signals from the camera into GPI signals to pause and resume the recorder when it is in record mode. In addition to the device control, there will also be XLR Balanced line input to be converted to unbalanced line level. There is also the possibility of getting it to communicate with the nNovia RS-422 port and using this protocol to control the device. I'm still working on the final design. I have built the PIC 16f872 based circuit that controlls the nNovia via the GPI control lines and this seems to work very well. The next step with the PIC interface is to try controlling the RS232 port on the nNovia to start and stop the deck and get its status. I will be prototyping the Preamp shortly. I have a plan to use the...

tags

electronics22
coding13
microcontroller9
radio7
Computer6
hacker6
micro6
wayback6
arduino5
camera5

Show more Show less

arc

2026 10
- Aug 2026 10
  - Aug 10 1
  - Aug 08 9

2023 1
- Mar 2023 1
  - Mar 02 1
2019 1
- Oct 2019 1
  - Oct 31 1
2018 7
- Oct 2018 1
  - Oct 12 1
- Sep 2018 2
  - Sep 21 1
  - Sep 18 1
- Jul 2018 4
  - Jul 24 3
  - Jul 15 1
2015 2
- Mar 2015 2
  - Mar 07 2
2014 2
- Nov 2014 1
  - Nov 02 1
- Feb 2014 1
  - Feb 06 1
2013 1
- Jan 2013 1
  - Jan 31 1
2011 4
- Jun 2011 1
  - Jun 22 1
- Mar 2011 2
  - Mar 16 1
  - Mar 09 1
- Feb 2011 1
  - Feb 08 1
2010 14
- Dec 2010 2
  - Dec 06 1
  - Dec 01 1
- Nov 2010 5
  - Nov 30 1
  - Nov 17 1
  - Nov 16 1
  - Nov 12 1
  - Nov 11 1
- Oct 2010 1
  - Oct 08 1
- Sep 2010 1
  - Sep 30 1
- May 2010 1
  - May 05 1
- Apr 2010 1
  - Apr 29 1
- Mar 2010 1
  - Mar 11 1
- Feb 2010 1
  - Feb 05 1
- Jan 2010 1
  - Jan 27 1
2009 4
- Nov 2009 2
  - Nov 06 1
  - Nov 05 1
- Jun 2009 2
  - Jun 14 2
2008 6
- Oct 2008 2
  - Oct 18 1
    
    XBee USB
  - Oct 17 1
- Aug 2008 1
  - Aug 03 1
- Jun 2008 3
  - Jun 25 2
  - Jun 19 1

Show more Show less

subs

Posts

Posts

All Comments

All Comments